> telescopic gate
For when space behind the fence is tight
Leaves stack into each other as they open, so you get full access without needing a long run-back.
Custom automatic gates for Sydney homes
Designed, fabricated and installed by one Sydney team, with automation and access control built around your property.
> the custom difference
We design the perfect gate to match your home
Made for your property
Every opening is different. We measure the driveway, levels and frontage, then design a gate that follows the property instead of forcing a standard panel into place.
Australian made, in-house
We fabricate every gate ourselves, from its aluminium frame through to its powder-coated finish. Nothing is pulled from a catalogue or imported as a ready-made kit.
One team throughout
UNIGATE coordinates the gate, automation and supporting trades from the first site measure through to installation and handover. You deal with one team throughout.
We service all Sydney suburbs
We design, fabricate and install custom automatic gates across Greater Sydney; from the eastern suburbs and north shore to the inner west, hills and beyond.
> gate types
A gate for every type of Sydney driveway.
We offer a range of gates to suit every type of Sydney driveway. Whether you have a small, medium, or large driveway, we have a gate that will suit your needs.
> swing gate
For classic entrances with room to open
Single or double leaves swing inward or outward — ideal when you have clear driveway space.
> sliding gate
For when there's a wide opening
The leaf slides parallel to the fence line, so you don't lose driveway space to a swinging gate.
> corner turning gate
For sites that turn around a corner
The leaf tracks around an angle, following the fence line where a straight slide won't fit.
> corner gate
For L-shaped or angled entrances
Built to wrap a corner cleanly, matching awkward property lines without a patchwork of separate gates.
> cantilever gate
For when the ground can't take a track
The leaf hangs and slides without a ground rail — better over uneven driveways, steep grades, or soft ground.
> the process
In depth process
01Get in touch
Tell us about your property, driveway and what you want from the entrance. Photos and a rough opening width help us get started.
02We come out and measure
We visit the site to check the opening, driveway levels, available run-back, access and any structural or electrical work required.
03Design the gate
We develop the gate type, proportions, materials, finish, automation and access controls around the measurements and your home.
04Fabricate & Install
Our team coordinates fabrication, site works, automation and installation, then tests the complete system with you before handover.
We're with you for the long run
Every home is unique. We work fully custom, meaning every quirk and detail of your driveway is accounted for, ensuring your new gate fits perfectly with your home’s unique situation.
> the unigate difference
We provide a turnkey service for your new gate
01
Design & fabrication
A custom entrance designed for the proportions, architecture and practical needs of your property.
02
Ground & structural works
Excavation, concrete, brickwork and rendering coordinated as part of the complete build.
03
Automation & access
Reliable motors, electrical services, intercoms and access control brought together correctly.
04
Installation & handover
Every trade aligned through one point of contact, right through to the finished result.
One company.One point of contact.One complete solution.
Get started
> frequently asked
Frequently asked questions
Planning a new automatic gate? Get clear answers from a team that designs, fabricates and installs complete gate systems.
The cost of a custom automatic gate depends on the driveway width, gate type, materials, motor and access controls, plus any electrical, structural or ground works. Unigate assesses your property first, then provides a quote for the complete scope so you can see what is included.
The best gate depends on the space beside and behind your driveway, the slope, ground conditions and how the entrance needs to operate. Unigate designs sliding, swing, telescopic, cantilever, corner and corner-turning gates, then recommends the configuration that fits your property.
Yes. Every gate is measured and designed for the property rather than selected from a standard kit. Telescopic gates can reduce the run-back needed, cantilever gates avoid a ground track, and corner-turning systems can follow an angled fence line where a straight sliding gate will not fit.
Yes. Unigate designs and fabricates its custom gates in Australia, then manages installation and handover. Keeping the work in-house gives the team control over the gate's dimensions, finish and automation setup.
Unigate commonly specifies powder-coated aluminium for coastal properties because it resists rust and places less weight on the gate motor. The final material and finish are chosen to suit your site, the design of your home and the level of privacy you want.
Your gate can be planned with a suitable motor, electrical services, intercom and access control as one system. The right setup depends on who needs access, how often the gate will operate and how you want visitors or deliveries to enter.
Unigate can coordinate the site measure, design, fabrication, ground and structural work, electrical services, automation, installation and handover. You have one point of contact instead of arranging separate gate, building and electrical contractors yourself.
The timeline depends on the design, fabrication, automation and any supporting trade work required at your property. After the site assessment and scope are confirmed, Unigate can give you a project schedule based on your gate rather than a generic estimate.
Yes. Unigate provides aftercare once your automatic gate is installed, and your first motor service is included. The team will also explain the completed system at handover so you know how to operate it and arrange future maintenance.